Jiujiang Deep Sea Technology Development Co., Ltd.

Magical effect! Making leather yellowing remover---the core logic of silicone oil viscosity selection

May 08, 2025

info-575-376

When making leather yellowing remover, the viscosity of dimethyl silicone oil should be selected based on comprehensive consideration of product form, penetration performance, film-forming effect and industry practice. The following are specific analysis and suggestions:

 

 

One. The core logic of viscosity selection

 

 

Product form adaptation

Liquid spray type: It is recommended to use 50-100 cSt low viscosity silicone oil. For example, the fluidity of 50 cSt silicone oil is close to that of water, which can quickly penetrate the pores of leather and work with the yellowing-removing ingredients. Cream/paste type: It is recommended to choose 350-500 cSt medium-to-high viscosity silicone oil. This type of silicone oil can provide appropriate consistency to prevent the product from running off too quickly, while forming a durable protective film on the leather surface. Special needs (such as long-term protection): If you need to enhance anti-fouling properties, you can try high-viscosity silicone oil above 1000 cSt, but be aware that it may affect permeability.

 

Balance of penetration and film formation

Low viscosity (50-100 cSt): Small molecule silicone oil easily penetrates into the leather fiber, assisting in removing deep yellowing, but the surface film formation is weak. Medium-high viscosity (350-500 cSt): Large molecule silicone oil forms a uniform hydrophobic film on the surface to prevent secondary oxidation, but the penetration ability is limited. Mixed use: 50 cSt (penetration) and 350 cSt (film formation) can be compounded in a 1:1 ratio to take into account both cleaning and protection.

 

Industry practice reference

In the formulation of leather care agents, 350 cSt is the mainstream choice. For example, in the Baite BT201-350 series, 350 cSt silicone oil is often used in leather brighteners, which has both lubricity and stain resistance. Laboratory oil baths often use 50-100 cSt silicone oil because of its good fluidity and is suitable for fast-acting scenarios. High-viscosity silicone oil (such as 500,000 cSt) is mostly used in industrial-grade protective coatings and is not suitable for civilian yellowing agents.

 

 

Two. Key Performance Parameters

 

 

Viscosity (cSt) Typical application scenarios Advantages Disadvantages
50 Liquid spray/penetration type Quick penetration, auxiliary decontamination Weak film-forming property, easy to volatilize
100 Universal yellowing remover Balanced penetration and film-forming property General long-term effect
350 Cream/anti-fouling type Long-lasting protection, enhanced gloss Slow penetration
500 High-end leather care agent High anti-fouling property, anti-scratch Requires emulsifier
1000+ Industrial protective coating Durability in extreme environments Difficult to disperse, high cost

 

 

Three. Purchasing Notes

 

 

Suppliers are required to provide kinematic viscosity (25°C) test reports to ensure compliance with nominal values. Food-grade / cosmetic-grade silicone oils are preferred to avoid impurities in industrial-grade products that may affect leather quality.

 

 

Experimental verification steps

 

 

Small-scale tests were conducted to prepare yellowing removers with different viscosities of silicone oil, and the penetration rate, drying time and yellowing improvement effect were tested on cowhide leather scraps. Observe pH stability: After storing the formula for 7 days, use pH test paper to detect whether there is any change in acidity or alkalinity. Before pilot optimization and mass production, test centrifugal stability: centrifuge at 3000 rpm for 30 minutes to observe whether there is stratification. Simulate high temperature and high humidity environment (40℃, 80% humidity) for 1 month to evaluate the shelf life of the product.

 

 

Five. Summary

 

 

Preferred viscosity: 350 cSt (balanced penetration, film formation and stability). Alternative: Rapid penetration requirement: 50 cSt. Long-term protection requirement: 500 cSt. Note: Avoid direct mixing with strong acids and alkalis, give priority to food-grade silicone oil, and strictly perform compatibility testing. The above methods can ensure that dimethyl silicone oil plays the best role in leather yellowing remover, while taking into account product performance and cost.

 

goTop